MAIN PAGE » KTM » KTM 1290 » 1290 R/SE - 2014-16 » Clutch release / pressure plate ORANGE KTM 1290/1390 SDR/GT LC8 Motor




Clutch release / pressure plate ORANGE KTM 1290/1390 SDR/GT LC8 Motor
- Product No.:
- SDF-009/OR-A5
- Shipping time:
-
immediately ready for dispatch (abroad may vary)
- Stock:
- pieces
- Weight:
- 0.1 kg per piece
Clutch release / pressure plate ORANGE KTM 1290/1390 SDR/GT LC8 Motor
- Manufacturer:
SEVENTYONE S.R.L.
Zona Industriale Palù, 6G - 38055 Grigno (TN)
Phone: +39 0461 780184
info@evotech-rc.it
General safety instructions for the product:
We recommend that you always consult a specialist workshop when fitting our products or have this work carried out by a specialist. If you fit it yourself, please make sure that your motorbike is secure and that the product is only intended for your motorbike. The models for which the product is tested and intended can be found with each item.
To avoid damage to your motorbike during installation, we recommend covering all important/sensitive parts.
When fitting, use threadlocker if possible and observe the torque specifications. The fixing screws on the licence plate holder in particular should be secured with threadlocker. Loss of the licence plate holder due to lost screws can cause unpleasant damage.
General torque specifications can be found HERE
The legally required licence plate angle of 30 degrees can be set on the Italian licence plate holders
Information for our Austrian customers specifically for the type approval and registration of licence plate holders can be found HERE
Unfortunately there are no reviews yet. Be the first who rates this product.
You must be logged in to submit a review. Login
Customers who bought this product bought also the following products:
.jpg)
Are you looking for a stable and visually clean solution for mounting your number plate?
We offer a 3 mm thick, 150 gram light DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the number plate.
The plate is matt black on one side and glossy black on the other.
For our customers from SWITZERLAND or LICHTENSTEIN we also have the right size in stock: 140 x 180 mm plate
For our customers from Austria we can recommend this plate: 210 x 170 mm
The plate is supplied without holes.
We used 5 mm countersunk screws for mounting on a KTM Super Duke R 1.0.
It is best to use a pillar drill with a depth stop for this.
To secure the M5 cap nut we use Loctite 243.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE number plate holders. If not, you can get it HERE.
Alternatively, we also offer a higher-quality reflector kit: REFLEKTORKIT
15,73 Dollar

Optimal protection for swingarm and fork with a slight fall or overturning of the motorcycle.
Good protection for expensive motorcycle parts. Mounting on the rear wheel axle.
Assembly time approx. 10min. each axis
Weight: 220 grams per axlespare parts.
INSTALLATION
Good protection for expensive motorcycle parts. Mounting on the rear wheel axle.
Assembly time approx. 10min. each axis
Weight: 220 grams per axlespare parts.
INSTALLATION
75,02 Dollar

Protection for clutch cover - ORANGE anodized incl. 2 longer screws.
Fits the original clutch cover and the transparent clutch cover from EVOTECH S.R.L.
CNC milled from aluminium.
The colour of the anodisation may change slightly when exposed to heat. This is not a reason for complaint, as it is unavoidable.
HERE there is a matching YOUTUBE video........
Fits the original clutch cover and the transparent clutch cover from EVOTECH S.R.L.
CNC milled from aluminium.
The colour of the anodisation may change slightly when exposed to heat. This is not a reason for complaint, as it is unavoidable.
HERE there is a matching YOUTUBE video........
66,55 Dollar
This product was added to our catalog on Tuesday, July 24, 2018.